Horizons Unlimited - The HUBB

Horizons Unlimited - The HUBB (https://www.horizonsunlimited.com/hubb/)
-   Yamaha Tech (https://www.horizonsunlimited.com/hubb/yamaha-tech/)
-   -   Help! - Yamaha Tenere (3AJ) engine sound (https://www.horizonsunlimited.com/hubb/yamaha-tech/help-yamaha-tenere-3aj-engine-85104)

erdei82 10 Jan 2016 13:26

Help! - Yamaha Tenere (3AJ) engine sound
 
Hi,

I have just bought my first Tenere, and I love it! :clap:

As this is my first one, could you please listen to its engine sound and tell your opinion about it? Unfortunately I have no experiences about the sound of a Tenere but I found it a bit knocky. Is something wrong, or is this 'normal'? If there is a problem, what should it be? :helpsmilie:

The video has been shoted after a cold start.



Thanks a lot!

erdei82 10 Jan 2016 13:28

Video link
 
https://www.youtube.com/watch?v=rEbn0hJm9Ts

Jens Eskildsen 10 Jan 2016 13:40

Sounds a bit like the lovechild of pistonslap and loose valves. :D

Check the valveclearences, its pretty easy.

steveloomis 10 Jan 2016 17:02

I agree, sounds like valve clatter. Adjustment not hard, just fiddly. When you pull the "feeler gauge" thru the gap it should have some resistance. The trick is to be able to tighten the jam nut and not alter the clearance. I made a tool from a piece of brass tubing that fit over the square adjustment screw, wrapped the top of the brass tube with tape to make it easier to hold while tightening the jam nut. Recheck the clearance after tightening the jam nut and if not perfect do it again.

I just watch the rocker arm and when it is up I adjust that one.?c?:welcome:

Mezo 11 Jan 2016 05:17

Üdvözöljük Erdei, úgy hangzik, mint a szelephézagot nekem.

Tudta Ön, lovagolni ezt a csoportot?



Mezo.

jjrider 11 Jan 2016 11:14

That sounds way more than valves . Take your sparkplug out , turn the motor over by hand with a socket on the flywheel nut. Using something like a 3/8 dowel(or for now a drinking straw) and spin the motor over till the piston comes to TDC the starts to go back down. Make sure that the piston has moved some downward. Now with a dowel push down on the piston to see if it'll move any little bit without the crank turning.

xtrock 11 Jan 2016 14:06

Doesnt sound good, this is more what its suppose to sound.

https://www.youtube.com/watch?v=2l82Sze0Nvk

xtrock 11 Jan 2016 14:07

Quote:

Originally Posted by Mezo (Post 526658)
Üdvözöljük Erdei, úgy hangzik, mint a szelephézagot nekem.

Tudta Ön, lovagolni ezt a csoportot?



Mezo.

Nice video, here is some more enduro fun..


https://www.youtube.com/watch?v=pKT6OIkXS_I

erdei82 12 Jan 2016 19:33

Thanks!
 
Thank you all for your replies and support! :thumbup:

I will check the valve clearance first and see if the noise is gone or not.

@Mezo: As this is my first Tenere I will get her in shape till spring and I am going to get in touch with the hungarian Tenere Club. It's their video you have posted. :) Hopefully I will be participating in the next one. :mchappy:


All times are GMT +1. The time now is 13:15.


vB.Sponsors