5Likes
|
|
10 Aug 2002
|
Registered Users
HUBB regular
|
|
Join Date: Mar 2001
Location: Perth, Western Australia
Posts: 71
|
|
R80GS Vs R100GS
Just doing the sums and there's about a AUD $5000 (US $2500) difference between the R80GS and R100GS, so if I was to purchase the R80GS and put the spare cash (who's got spare cash these days?) into 'jazzing' up the bike mechanically (Munich Motorcycles - and this is not intended to be a commercial plug) am I on the right tangent, or go for the R100GS.
The bike is for two-up travel, and I note that Grant does recommend either the 80 or 100 for two-up (I actually prefer the Tiger but that's another storey).
Also guys & gals what would be the preferred options to the 'winner'?
------------------
Macca & Lynda
Without adventure life is in full decay.
__________________
Macca & Lynda
Tiger955i
|
11 Aug 2002
|
|
Gold Member
Veteran HUBBer
|
|
Join Date: Feb 2001
Location: Reno,NV,USA
Posts: 560
|
|
I think that the R100GS would be better.
A little more horsepower and torque.
With the paraleaver. The driveshaft will have to be replaced every 40,000 miles but it gives you a longer wheel base and you can use the tubeless trie wire wheels.
There are some fixes that should be done to the transmission and electrics but over all
they are good bikes that can be overloaded and abused.
Grant has put 1000cc jugs on his GS and is thinking of adding a paraleaver.
I am not sure which is easer (cheaper?) converting a R80GS to a R100GS or buying a R100GS and fixing its problems.
Good luck, John.
|
11 Aug 2002
|
|
HU Founder
Veteran HUBBer
|
|
Join Date: Dec 1997
Location: BC Canada
Posts: 7,324
|
|
Here's the differences that matter between and R80G/S and R100GS
(please note carefully the G/S as opposed to GS. The R80G/S is a monolever produced from 1981 to 1987, the GS is a paralever produced in various forms including specific country models, in both R80GS - 800cc and R100GS - 1000cc versions, after the end of the G/S run, to about 1997)
G/S has wimpy forks, GS forks much better.
G/S is tube type tires, GS is tubeless.
G/S has durable monolever, extremely reliable oil bath driveshaft, GS has paralever, technically better system, eliminates "jacking" but is limited in life - 40-50,000 miles, is much heavier, but is longer by 1 1/2 inches approximately, (better for two-up) has 4 bolt pattern wheel and stronger hub, and allows tubeless wheels / tires to be used.
R80G/S has small battery, GS has much larger battery on same electrical system.
G/S has reliable Bosch starter motor, but it doesn't spin the engine over as well as the less-reliable GS Valeo.
G/S is lighter because of: small spindly fork legs and small disk brake, smaller gas tank, shorter subframe and seat, monolever swingarm is much lighter than paralever, minimal headlight assembly as opposed to massive headlight shrouding etc on GS and even worse the bars around the headlight on the Dakar models. Even things like the sidecovers are smaller on the G/S, the centerstand is smaller etc all add up to a significant weight difference.
The G/S is over 40 pounds lighter, but some of that disappears in prep for overlanding. Also things like the GS battery, while double the weight, are a no-brainer. If you have the choice, always go for a bigger battery on an electric start bike, especially one that is notorious to kick, or may not even have a kickstarter.
Engines and transmissions and electrics are effectively the same, so all the problems and their cures - and there IS a cure for ALL ills on both - is esseentially the same.
For the nitpicker who says there isn't a cure for the driveshaft - there is - replace it regularly like any maintenance item, e.g. the timing chain.
Both rear subframes, while different in dimensions and layout, are weak and need major bracing.
As for Johns comments about which is easier/ cheaper to prep for overlanding - If I were starting fresh I'd go for the GS (not the Dakar) and do what is needed - much easier than adding a paralever to a G/S, trust me, it's not simple, the frame needs mods.
For me, the tubeless wheels are a big plus, also the bigger battery and much stronger and better damped forks make the GS the winner. Feel free to disagree, but that's my choice.
Remember I have a G/S because that's all there was in 1986.
By time I'm done it WILL BE a GS. All that's left to do is the swingarm, and I have that, just need the time.
Hope that clarifies the options a little, in the end it's your choice, and your pocketbook, and your own mechanical skills that determine which is best for you.
There are of course new bikes to look at, the Suzuki V-Strom being worth a look - the reports are good, people like the bike, but it's no off-roader, somewhat similar to the Tiger from what I can gather.
And the R11xxGs is still a major contender if you're mostly into good roads.
------------------
Grant Johnson
Seek, and ye shall find.
------------------------
One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.
------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
|
11 Aug 2002
|
Gold Member
Veteran HUBBer
|
|
Join Date: Mar 2001
Location: British Columbia
Posts: 246
|
|
Grant covered the bases, and again: are we talking 80GS or 80G/S? The 80GS being a smaller engined R100GS as Grant pointed out. I have had both the R100GS (past) and the R80G/S (present). The better susupension on the later, Paralever models, is worth the weight for two up. You will spend a lot of money getting a G/S to handle as well as the later bikes. I do find the G/S better off road, on my own. Mainly because of the reduced weight, and the bike just feels smaller. Keep in mind also that tire choices are getting limited for the 18 inch, narrow rear wheel of the G/S. As manufacturers change their lineup of tires, the older, less popular sizes tend to get dropped.
On thing that is worth mentioning is the smoothness of the engine. the 800cc engine has always been renowned as one of the best 'airheads'as vibration is minimal. I found my R100 shook quite a bit more at speed then my R80G/S does. Also, the 800cc engine in the G/S runs at lower compression, and is better on low octane fuel. Again, my R100 wasn't happy on anything less then 91 octane til I dual plugged it. The brakes on both bikes are marginal, but more so on the older G/S. Definitely inadiquate two up loaded - the origional 'ABS'
|
11 Aug 2002
|
Registered Users
Veteran HUBBer
|
|
Join Date: May 2002
Location: Back in Asia
Posts: 322
|
|
Hey Macca
Munich M/cycles has a R100GS P/D in there for sale, well it was a couple of weeks back when I was there.
I have a '91 model that I brought back from Germany and it has done 47,000 km and is a real workhorse! I have also a R1150 Adventure still in Perth (ridden from Cairns) and it is also a great bike. Grant's wrong as it is a better bike on the dirt as I rode over there through the centre all dirt! It is better than my R100GS! But I have short legs too so have to stand on the pegs and actually ride the bike.....haha.
Ok mate, I will be back over there soon so give us a call and I will help if I can. Ph:0417 580 272.
Cheers mate
Ivan
|
11 Aug 2002
|
|
HU Founder
Veteran HUBBer
|
|
Join Date: Dec 1997
Location: BC Canada
Posts: 7,324
|
|
Actually I agree that the R11xxGs is "better" on the dirt - BUT - and it's a big BUT - two-up with luggage, it's just overall too heavy - ANY mistake and you're in unrecoverable territory, whereas the lighter R100GS / G/S - while also too heavy - is enough lighter that there is more hope of recovery. But let's face it - they are ALL too heavy to do anything serious off-road.
Of course it depends a lot on your skills - a better rider will find the R11 fine off-road, and do some amazing things with it, BUT MOST PEOPLE will find it to be just too heavy in rough going. The high weight is intimidating to most riders, and means that the less skilled can't make ANY mistakes or they are going to fall. But of course they WILL make mistakes, and picking it up is no picnic.
The feedback I have had is generally that people find that the airheads are "better" OVERALL, all things considered, in the rough stuff.
For ME, I think the oilhead is MARGINALLY better handling in the rough stuff, UNTIL I make a mistake - then I want the airhead. And although I haven't personally dropped an oilhead, I have helped pick one up a number of times...
I don't think that either is enough better off-road to make it a deciding factor either way.
The real decider - for most, the carnet is the single biggest expense in a major tour - and the airhead GS wins hands-down, as it has a MUCH lower "book" value, thereby lowering the cost of the carnet by a huge amount.
YMMV... everyones skills and experience is different.
------------------
Grant Johnson
Seek, and ye shall find.
------------------------
One world, Two wheels.
www.HorizonsUnlimited.com
__________________
Grant Johnson
Seek, and ye shall find.
------------------------
Inspiring, Informing and Connecting travellers since 1997!
www.HorizonsUnlimited.com
|
12 Aug 2002
|
Registered Users
HUBB regular
|
|
Join Date: Mar 2001
Location: Perth, Western Australia
Posts: 71
|
|
Well guys I've gotten some excellent feedback, and at the end of the day, as I'm searching for the 'right' bike, I know I'll be in for some (serious?) modifications regardless.
Ivan, Lynda tells me you contacted me but I was still overseas, I trust you got intouch with Jeff (R80 Uk-Africa). Yep I will ring you as I want to see your set-up as I have checked out Jeff's. I've got Paul of Munich M/mycles on the lookout for a Rxx(xx)GS for me.
To finish off with I trust no one has copyrght rules on their various 'projects' as I'm busily compiling (read plagerising (sp)) what changes (if any) I will (or Munich M/cycles) be doing.
Happy trails.
------------------
Macca & Lynda
Without adventure life is in full decay.
__________________
Macca & Lynda
Tiger955i
|
20 Jan 2010
|
Registered Users
Veteran HUBBer
|
|
Join Date: Oct 2002
Location: Stockholm - Sweden
Posts: 317
|
|
I have one comment to add.
It is possible to push-start a 800cc.
It is not possible to push-start 1000cc... I have tested...
When I lost an exhaust valve on my 800cc I had to choose with my wallet, not a smart choice but about 200EU difference between 800cc and 1000cc was enough to push me over better judgement.
Today I would stick with 800cc displacement, and improve that by 9.2:1 pistons, dual-plugging and lowering of the barrels instead of the heads. 44/38 valve conversion. => About 10.5:1, and about 60hp and about 6kg torque - push start possible any season -
Or if you are to ride in areas with poor petrol, Egyptian Police conversion is an option (still 800cc).
Question to all of you who ride and advocate 1000cc - have you ever needed the extra power over 800cc ?
What is your explicit reason to choose 1000cc over 800cc (I do not refer to GS vs G/S - the cc displacement can be interchanged) ?
The only reason for 1000cc that I can apprechiate is highway fast touring (>80mph / >140km/h)... and off-road is not freeway, autobahn, motorway, highway, high speed cruising...
__________________
Drive Safely,
Albert
|
20 Jan 2010
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Apr 2001
Location: Norway
Posts: 1,379
|
|
Quote:
Originally Posted by dc lindberg
It is possible to push-start a 800cc.
It is not possible to push-start 1000cc... I have tested...
|
I have push-started my 1000cc (Siebenrock), it’s not fun but not much worse then a 800cc.
Quote:
Originally Posted by dc lindberg
Question to all of you who ride and advocate 1000cc - have you ever needed the extra power over 800cc ?
|
First of all, both 800cc and 1000cc works great. When I upgraded my 800cc to 1000cc it was mainly because my pistons wore out. I’m not a fan of the original 1000cc BMW-piston either but it works for a long time.
For me the extra power (and torque) is nice, my first thought after the conversion was “why didn’t I do this earlier?”. I like to drive a powerful bike, if that’s not important then there is no need to change anything.
Personally I like to have 75-80 Nm at 3500 RPM.
Quote:
Originally Posted by dc lindberg
What is your explicit reason to choose 1000cc over 800cc (I do not refer to GS vs G/S - the cc displacement can be interchanged) ?
|
If I should buy a “new” bike today I wouldn’t cared much if it was a R80 or R100, but it would probably end up as a R100 (or bigger) with a R80 beveldrive.
Quote:
Originally Posted by dc lindberg
The only reason for 1000cc that I can apprechiate is highway fast touring (>80mph / >140km/h)... and off-road is not freeway, autobahn, motorway, highway, high speed cruising...
|
The R80GS can keep a speed that will make you deaf and tired. When it comes to road-driving I would say that the strength of the R100 is when you are passing cars or are having fun on twisty roads. If you drive 2-up or with luggage the extra power comes inn handy.
I find the R80 better on very technical sections because it runs smoother then the R100 on low revs but if you use lighter pistons on the R100 you have the best of both worlds.
The R80 is geared a tad lower, which is nice.
For me the negative aspect with a R100 is the need of an oil-cooler. I don’t need it on a R80 but for the R100 I had to install it.
I have driven 200kkm with a R80 engine and 45kkm with a modified R100 engine and maybe a few thousand kms with a standard R100. Personally I think that the modified R100 is the best, followed by the R80. In the end it doesn’t matter much unless you are an engine-geek like me.
|
20 Jan 2010
|
|
Contributing Member
Veteran HUBBer
|
|
Join Date: Mar 2005
Location: Northumberland, uk
Posts: 761
|
|
I have an r80gs - without going into all the mods I have done over a period of time I would say go for the R80gs and fit seibenrock 1000cc upgrade kit, you gain better torque and power delivery than a standard 1000, smoother, smaller carbs give better low down control and a spare set of barrels and pistons in the garage if something goes wrong and by the sound of it still a much cheaper option in oz.
|
30 Jan 2010
|
Registered Users
Veteran HUBBer
|
|
Join Date: Oct 2002
Location: Stockholm - Sweden
Posts: 317
|
|
Quote:
Question to all of you who ride and advocate 1000cc - have you ever needed the extra power over 800cc ?
What is your explicit reason to choose 1000cc over 800cc (I do not refer to GS vs G/S - the cc displacement can be interchanged) ?
|
Thank you for your reactions and thoughts on these two questions -
What you did reply is:
- never needed it
- have none
What you did reply is that you enjoy and apprechiate the extra power, and that is undisputable, but not an answer to the questions; it is avoiding the questions.
What you did add as very important feed-back is:
- 1000cc need an oil-cooler
- 800cc runs smoother
If I am correct the 800cc is easier to kick-start than the 1000cc? That would be an important sideeffect to consider as well if so.
The weight differences, 1kg lighter for the 1000cc is as far as I see it hardly of any importance.
My experience is that too much power and torque complicates driving when it is not needed. When I had 800cc I really wanted 1000cc - especially for the winter season. Now, with Siebenrocks 1000cc kit, I regrett my choice just about everytime I drive - too much power; loose tracktion too easilly on the rearwheel, spinning all the time and causing skidding sideways when I do not what it.
Stated reasons 1000 over 800; the revs, luggage, pillion, overtaking - sure; I do agree that 800cc did lack that power, especially from around 90km/h (55-60mph) and up. In mudd/sleat/inches of snow - ok, then the extra power does make driving more fun and "inspired", but I do not -need- that extra power, it only makes it possible to go faster and that's all.
Another thing I do notice is that is does require the battery to be in better shape to start a 1000 vs an 800... and that -is- a down-side.
So all in all - I am not for 1000 if to drive in desolete areas. I would go for 800cc, 44/38(37) valves, perhaps only 9.2:1 and single plugged, but I would probably raise the compression ratio to 10-10.5:1 to get the best mileage, dual-plugged with the simplicity and safety of Daniel Dicke ; perhaps retro fit the canister with the braker-point (tip of memeber of this group in another string); since this solution gives just about the hp-power of the 8.2:1 1000 version of 60hp, just a bit less torque, freeway power just enough to carry a heavy load and pillion and still keeping the smoothness of the 800. 800 with raised compression needs an oilcooler though!
Friend of mine advocates 900; it presents the best of the two worlds 800 and 1000 he says.
So I can not say that I ever -need- the extra power of 1000. I love the power at summer on the freeways though!
My explicit reason to choose 800cc are as listed; less demand on the battery at start, easier to kickstart (if I am correct), smoother running and easier to control power, cooler running engine. Can not see any practical reason for more power - only fun-factor and ego reasons - -
__________________
Drive Safely,
Albert
|
30 Jan 2010
|
|
Contributing Member
Veteran HUBBer
|
|
Join Date: Mar 2005
Location: Northumberland, uk
Posts: 761
|
|
Hey Albert - If an upgrade 1000cc from 800cc is for ego reasons then someone has a very strange ego. I have got to say as I travel two up quite a lot then the 800 was underpowered for such a large bike even at 1000cc its not a powerful machine by any standard and there are any amount of 600 cc bikes putting out this kind of power without the weight if you dont need the room for a pillion. I really cant imagine the bm being the bike of choice for ego. its a great choice for comfort - 2 up this is where it outshines the 600s available,simplicity and enduring build quality along with being very ridable in such a variety of conditions.
I have to say I feel there is little difference in kickstarting the bike now (as a 1000cc to when it was a 800cc) and I use the kickstart 80% of the time especially if the bike has been laid up a while. But its whatever floats your boat - so to speak.
|
30 Jan 2010
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Apr 2001
Location: Norway
Posts: 1,379
|
|
Quote:
Originally Posted by dc lindberg
What you did reply is that you enjoy and apprechiate the extra power, and that is undisputable, but not an answer to the questions; it is avoiding the questions.
|
Hehe, you can read the replies and understand it as you like.
As I wrote earlier I think both the R80 and R100 are great bikes, but my favorite is a R100 (or bigger) with light pistons. For me the only downside is that I need the oil-cooler, but I can live with that. Most bikes have radiators anyway.
Quote:
Originally Posted by dc lindberg
My experience is that too much power and torque complicates driving when it is not needed. When I had 800cc I really wanted 1000cc - especially for the winter season. Now, with Siebenrocks 1000cc kit, I regrett my choice just about everytime I drive - too much power; loose tracktion too easilly on the rearwheel, spinning all the time and causing skidding sideways when I do not what it.
|
I agree on this if we compare standard R80 and standard R100. If you have a well tuned R100 (or bigger) with light pistons, the right camshaft etc the power delivery is smoother then the R80.
Quote:
Originally Posted by dc lindberg
Another thing I do notice is that is does require the battery to be in better shape to start a 1000 vs an 800... and that -is- a down-side.
|
Get a starter from Nippon Denso
Quote:
Originally Posted by dc lindberg
My explicit reason to choose 800cc are as listed;
|
Quote:
Originally Posted by dc lindberg
less demand on the battery at start,
|
The difference is minimal, with a ND-starter, it doesn't matter at all.
Quote:
Originally Posted by dc lindberg
easier to kickstart (if I am correct),
|
Minimal difference, I don't even have a kickstart.
Quote:
Originally Posted by dc lindberg
smoother running and easier to control power,
cooler running engine.
|
For a standard R100 yes, but not for a modified engine. The need of an oil-cooler is a drawback.
Quote:
Originally Posted by dc lindberg
Can not see any practical reason for more power - only fun-factor and ego reasons - -
|
Bikes are an ego-thing, and some people like to have fun.
|
30 Jan 2010
|
Registered Users
Veteran HUBBer
|
|
Join Date: Oct 2002
Location: Stockholm - Sweden
Posts: 317
|
|
-
Just laughing heartilly - I did get some emotional responses out of you guys -
Very good pointers Alibaba!
Most apprechiated. Point of this whole discussion is to present to the original thread composer that there are diffenrences and similarities; pros and cons; and that we all do have different preferations based both on solid facts and on personal subjective preferences.
To get a 1000cc smoother than an 800cc - that is a dream!
Hope that we have been able to present the views on 800cc vs 1000cc well to Macca. Probably he should go for the 1000cc, especially if he is doing some longdistance drives across the out-backs - flat surface does trigger some high-speed travelling.
The speeds we were doing across the mountains between Sweden and Norway back in 1994-1997, at winter with fully studded tires and skiis, was something like 80-90mph... and that was really heavy for my 800cc (9.2:1 with 44/40 and dual plugging, back then).
As for ego:
"plenty want's more!" -
__________________
Drive Safely,
Albert
|
7 Apr 2010
|
Registered Users
Veteran HUBBer
|
|
Join Date: Feb 2002
Location: Wessex, UK
Posts: 2,136
|
|
GS or G/S
When you say 80GS do you mean the paralever or the earlier G/S with the monolever? The latter has a shorter subframe, seat, not so good two up, and swinging arm with the driveshaft lasts a lot longer. If you use a paralever 80 or 100 GS try fitting the shorter rear shockabsorber from the R100R, it reduces the travel and improves shaft life quite considerably, mine has just developed a bit of play after 103,000 miles.
When travelling in developing countries with bad roads you rarely go very fast anyway so I would say the difference does not really matter so decide on the condition of the individual bike on offer, not engine size.
|
Currently Active Users Viewing This Thread: 2 (0 Registered Users and/or Members and 2 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...
2020 Edition of Chris Scott's Adventure Motorcycling Handbook.
"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)
Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.
Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.
Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!
What others say about HU...
"This site is the BIBLE for international bike travelers." Greg, Australia
"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK
"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia
"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA
"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada
"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa
"This is the answer to all my questions." Haydn, Australia
"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany
Lots more comments here!
Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook
"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.
Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!
New to Horizons Unlimited?
New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!
Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.
Read more about Grant & Susan's story
Membership - help keep us going!
Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.
You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.
|
|
|