Go Back   Horizons Unlimited - The HUBB > 4 wheels > Equipping the Overland Vehicle
Equipping the Overland Vehicle Vehicle accessories - Making your home away from home comfortable, safe and reliable.
Photo by Hendi Kaf, in Cambodia

I haven't been everywhere...
but it's on my list!


Photo by Hendi Kaf,
in Cambodia



Overlanders Handbook - everything you need to know, available NOW!

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 20 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Feb 2004
Location: United Kingdom
Posts: 602
Transmission noise

Hi

I'm 7 months / 34,000kms into my trip across Asia in a 1993 Toyota Hilux Pickup - 2.4D 4x4.

There's a backround noise when driving, which seems to come from the engine / front bulkhead. It's particularly noticeable through the clutch pedal, and is most apparent when revving the engine with the clutch down, or changing gear. The noise is then a light tapping, spinning-down noise. It sounds too light and external to be big end / main bearing noise. I would blame the clutch release bearing, or input bearing in the box, but wouldn't these be still when the engine is revved with the cluch pedal down? My suspect is a bearing in the PAS pump or alternator. The timing belt has done about 55,000 KM/S (not miles), and looks like new.

Theres a separate (I think) vibration, which is very apparent as you go into 4th at 45km/h through to about 50-55, then goes above this. It is worse when accelerating / going up hills. (This is in 2WD, I very rareley use 4WD). I have replaced the centre bearing, and had the UJs checked - there is a tiny amount of movement in them, but everyone says this is fine.

So I'm a bit stumped about this. It has been getting gradually worse over the last 20,000kms.

Any suggestions would be welcomed

Thanks

Daniel
__________________
4.5 years around Eurasia in a Toyota Hilux|http://eurasiaoverland.wordpress.com/
Pictures Here|https://picasaweb.google.com/113619413612674951960
Reply With Quote
  #2  
Old 20 Dec 2007
silver G's Avatar
Gold Member
Veteran HUBBer
 
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
Hi Daniel, just some quick thoughts:-
check the props again and grease the uj's and the sliders if you have them, I'm not sure there should be any play. Stick everything in neutral and see if there is more play than last time.
check engine and gearbox mountings
sorry, can't be more help.
Good luck
Chris
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
Reply With Quote
  #3  
Old 21 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: Saudi Arabia
Posts: 173
Hi Daniel,
Your thrust bearing is turning when you press the clutch in, that is why it's a bearing or in some cases a carbon type pad. I can't remember if your Toyota is a cable operated clutch or hydraulic, if it is cable then you need to adjust it to put some free play in it, about 1/8 th inch at the clutch fork. The thrust bearing would then clear the pressure plate in the off position and if it is the bearing that is causing the noise it will stop until you press the clutch. Some hydraulic systems also have an adjuster at the slave cylinder end.
I trust you have checked the oil in the gearbox.
Have you used the listening stick method to trace a noise ?
A long screwdriver or long socket extension touched to a unit and the other end at your ear while the engine is running.
BE MOST CAREFUL IF YOU USE THIS METHOD OF DETECTION AND MAKE SURE YOU HAVE SOMEONE WITH YOU.
After saying that I have used this method many times without misshap.

Cheers
Ian
Reply With Quote
  #4  
Old 21 Dec 2007
HU Sponsor
Veteran HUBBer
 
Join Date: Jul 2003
Location: Derbyshire, UK
Posts: 161
Hi. The vibration sounds like it could be a propshaft. It could simply be a weight that has come off the prop (they are tiny weights) or maybe a damaged or worn UJ. The other (main) problem sounds like the clutch release bearing. This is spinning with the clutch cover (that is bolted to the flywheel). Try sitting with the engine running and depress the clutch pedal and rev the engine on and off, up and down etc. If there is a problem with the release bearing you should be able to hear/feel it (maybe!).
It could also possibly be the input shaft bearing in the gearbox (like you say), I think this will make a humming sound under load or over run.
As a matter of course check the oil level in both gearboxes anyway.
Oh, and check the rear prop centre bearing again if you can.
To check the bearings in the PAS and alternator, place a big screwdriver (or similar thing) between your ear and the bearing area, press the flat screwdriver end on the casing near the bearing, then press your ear to the screw driver handle with the engine running. Be careful though, watch out for spinning fans, belts etc!! You can hear the noise of the bearings, they sound very noisy anyway, but if there is a worn one it sounds even more noisy! It's hard to explain, but play about with different sounds on the engine and you should be able to get a feel for what is normal. Or if you have a stethoscope, that's even better. You can actually buy proper stethoscopes for doing this very thing.

Right, that's a lot of writing for me, I'm off for a hot chocolate and a sit down...

Cheers,
Matt
__________________
www.mattsavage.com
VIAIR - 12 & 24 volt compressors and systems. Tyre levers, Land Rover parts, Sand Tracks, Allisport Intercoolers, Overland Prep, and much more...
Reply With Quote
  #5  
Old 21 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Location: Ghana
Posts: 289
I had a similar rattlly noise (well actually dozens) in the Defender - turned out to be the alternator. Fixed that and then the belt tensioner started... Sorry not much help!

I am off for a glass or two of Nederberg with our staff before we close down and I pack up the troopy to head for Mali tomorrow a.m.
Reply With Quote
  #6  
Old 21 Dec 2007
silver G's Avatar
Gold Member
Veteran HUBBer
 
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
Quote:
Originally Posted by gilghana1 View Post
I had a similar rattlly noise (well actually dozens) in the Defender - turned out to be the alternator. Fixed that and then the belt tensioner started... Sorry not much help!

I am off for a glass or two of Nederberg with our staff before we close down and I pack up the troopy to head for Mali tomorrow a.m.
Lucky bugger enjoy

stuck here in the cold with sausage butty
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
Reply With Quote
  #7  
Old 24 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Feb 2007
Location: Ghana
Posts: 289
Many thanks Chris!
got delayed a couple of days... :-( but now packed and checkinh fellow Hubbers for the last time for a while.

Hope everyone 'here' has a great Christmas and New Year
Gil
(curently enjoying a nice glass of water due to too much festive cheer last night)
Reply With Quote
  #8  
Old 24 Dec 2007
silver G's Avatar
Gold Member
Veteran HUBBer
 
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
Cheers Gil, looking forward to pictures
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
Reply With Quote
  #9  
Old 25 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Feb 2004
Location: United Kingdom
Posts: 602
A little bit more info.

I am not sure whether there are two problems, or if all the noises come from the clutch release bearing.

what sounds like a transmission noise is definitely strongest as the car picks up in 4th, but i can hear it now as the car picks up in any gear. perhaps there is some combination of engine speed and torque which makes it most noticeable in 4th... this implies the noise is related to engine speed, rather than road speed, so i do not suspect the propshaft. i had the whole thing off, a new centre bearing pressed on, and the ujs checked and greased. I don't think it's lost any weights, and the noises have been getting progressively worse, no sudden changes. at higher speeds in first, there is a judder in the delivery.

the gearbox oil is at the correct level, the correct grade, and has done maybe 10,000km.

my suspect is definitely the thrust (clutch release) bearing, though the bearing was brand new when i left. I ut a new clutch in 35,000km ago, but the car sat unused for a year, so perhaps some damp got into the bearing. the bearing is a closed type taper roller bearing which i didn't think needed greasing before use?

I don't really think it can be the input bearing, as this would definitely be still with the clutch down (for longer than it could take to spindown) and the vehicle stopped. i do have a spare though 9unlike the cluctch release bearing), so aside from the work involved in opening the box, it wouldn't be a disaster.

trouble is right now i'm in Iran, where there are no diesel cars, so no diesel specific spares, and i'm pretty sure the clutch / gearbox are different diesel vs petrol. i dare say it will hold out until pakistan, if not... well there's always DHhell.

thanks for your help guys, any more wisdom would of course be appreciated.

Daniel
__________________
4.5 years around Eurasia in a Toyota Hilux|http://eurasiaoverland.wordpress.com/
Pictures Here|https://picasaweb.google.com/113619413612674951960
Reply With Quote
  #10  
Old 27 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: Saudi Arabia
Posts: 173
Daniel,
You can eliminate the thrust bearing by disconnecting the cable/pushrod at the clutch fork and pushing the fork back to give the bearing clearance, when it is clear of the pressure plate it will not turn and so will not make a noise.
One possibility is the centre bearing in the end of the crankshaft that the end of the clutch shaft fits into. If this bearing has got so rough it can make the clutch shaft turn when the clutch is depressed. Can't think of an easy way to check this one though.
Sealed bearings shouldn't need greasing they are supposed to be greased during manufacture and standing for a year would not be a problem. I have just checked the thrust bearing on a gearbox that has been sat outside my villa for three years under cover in salty sea air and it is still smooth.
Cheers
Ian
Reply With Quote
  #11  
Old 30 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Feb 2004
Location: United Kingdom
Posts: 602
Hi Ian

Is the bearing you're talking about in the end of the crankshaft called the spigot bearing? It would be good if that was the culprit, as I have a spare...

Daniel
__________________
4.5 years around Eurasia in a Toyota Hilux|http://eurasiaoverland.wordpress.com/
Pictures Here|https://picasaweb.google.com/113619413612674951960
Reply With Quote
  #12  
Old 30 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: Saudi Arabia
Posts: 173
Yep,
Spigot bearing, first motion shaft bearing, clutch shaft bearing and clutch shaft centre bearing and probably more. It's about an inch or so in diameter the shaft having a small diameter end after the splines about an inch long that fits in the centre.
The only way to check this bearing is to remove the gearbox. This is the bearing that you have to align the clutch with so that the clutch shaft slides straight in.
Cheers
Ian
Reply With Quote
  #13  
Old 30 Dec 2007
Registered Users
Veteran HUBBer
 
Join Date: Sep 2007
Location: Saudi Arabia
Posts: 173
Warning

Daniel,
These bearings can be a Brd to remove. You need a small puller like a slide hammer, this fits inside the small hole and expands to grip the bearing track.
Without a puller you can hydraulic it out by packing grease in through the bearing hole and use a drift the exact size diameter of the end of the clutch shaft. Put the drift in the hole and hit it with a good size hammer. This method is messy and requires plenty of room to swing the hammer.
This method will not work if the bearing has started to break up as the grease will just come through the seals.
If the centre track has broken away from the outer track you have got problems as these tracks are hardened steel and difficult to drill.
DO NOT attempt to burn the track out as this will heat up the end of the crank and can damage the crankshaft oil seal.
In the past I have had to use a big chissle to crack the bearing track and then lever it out.
You really do need a puller as these other methods are a real pain and I had the use of a ramp in a vehicle workshop.
If you are not a mechanic then you need someone to do the job for you, with a slide hammer/puller it is a piece of p**s.
Cheers
Ian
Reply With Quote
  #14  
Old 19 Jan 2008
Registered Users
Veteran HUBBer
 
Join Date: Feb 2004
Location: United Kingdom
Posts: 602
OK, a quick re-cap on the situation.

I have two or three noises.

1) a tapping, spinning-down noise (not big end noise), when the engine is revved with the clutch pedal down (in any gear) and whjen shifting up through the lower gears whilst driving.

2) a vibration which makes the mirrors vibrate which is strongest as 4th gear is engaged (much less noticable at the same speed in 3rd), but which I think is also present in other gears

3) a whirring, meshing noise with the box in neautral, clutch pedal up. If I put the transfer case in neutral, and engage the gears, the whirring is greatest in 4th, though noticable in all gears.

I now have the gearbox out of the car. THe clutch release bearing was worn, it turns smoothly but the inner race is loose (rattles when shaken) inside the outer race. Seems to have got wet and lost lubrication. The flywheel also has a couple of hot-spots, and will be machined again. Looks like the clutch may have been slipping a little, though I think this was only ever at higher engine speeds in 1st gear. The spigot-shaft bearing is fine.

I've hand cranked the gearbox in all gears, and it is silent, and feels smooth apart from some the faint feeling of gears meshing, which the mechanics said was normal (I don't trust these mechanics though). There is also some lateral (i.e. side to side, not axial, front to back) movement, which the mechanics also tell me is normal.

1) I blame the clutch release bearing for noise (1), with the inner race rattling as the rotation of the flywheel / clutch pressure plate slows when the throttle is released.

2) Would a worn bearing or gear in the gearbox make the car shake as per noise (2)? 4th gear is (I think) straight-through (i.e. input and output shafts turn at same rate), which may lend the more movement, amplifying a vibration from another source. I think the engine mounts may be worn out - they will be replaced regardless.

3)Could the clutch release bearing be responsible for this whirring sound? Surely with the clutch up (when the noise occurs), the race which contacts the pressure plate (when the pedal is pressed) would be stationary within the outer race, which moves with the input shaft.

My dilemma is whether to open the gearbox. It feels OK, but it would be very annoying to put it back in and find that the noise is still there. The mechanics here in Pakistan don't have gear pullers (despite being an authorised, genuine Toyota Service Centre), but I think I can take the gearbox apart and inspect the bearings without needing a puller. Only problem is I don't have a new seal, though I have silicone RTV sealant.

Daniel
__________________
4.5 years around Eurasia in a Toyota Hilux|http://eurasiaoverland.wordpress.com/
Pictures Here|https://picasaweb.google.com/113619413612674951960
Reply With Quote
  #15  
Old 19 Jan 2008
Registered Users
Veteran HUBBer
 
Join Date: Aug 2007
Location: Sax, Spain
Posts: 901
Daniel My money is on 1st Thrust Bearing
2nd Spigot bearing.

Dessertstrom is right they are a PIG to get out without a puller!

If the engine is ticking over and in Neutral, and you depress the clutch and the noise GOES AWAY or gets Quieter its DEFINATELY the Thrust bearing.

Hope this helps

Martyn
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
G/S transmission 4 sale: Short 1st, Long 5th gears with kick ScooterNC TRAVEL Equipment for Sale / Wanted 7 12 Nov 2010 23:27
clicking / clacking noise Bradd Honda Tech 4 2 Aug 2006 21:11
AT Clutch noise Splint Honda Tech 6 22 Aug 2005 11:27
34L strange noise dougM Yamaha Tech 0 6 Jan 2003 09:44
chug chug noise! ben_travel Yamaha Tech 7 12 Oct 2002 00:20

 
 

Announcements

Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!

Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now
, and add your information if we didn't find you.

Next HU Eventscalendar

25 years of HU Events
Be sure to join us for this huge milestone!

ALL Dates subject to change.

2025 Confirmed Events:

Virginia: April 24-27 2025
Queensland is back! May 2-4 2025
Germany Summer: May 29-June 1 2025
CanWest: July 10-13 2025
Switzerland: Date TBC
Ecuador: Date TBC
Romania: Date TBC
Austria: Sept. 11-14
California: September 18-21
France: September 19-21 2025
Germany Autumn: Oct 30-Nov 2 2025

Add yourself to the Updates List for each event!

Questions about an event? Ask here

See all event details

 
World's most listened to Adventure Motorbike Show!
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...

Adventurous Bikers – We've got all your Hygiene & Protection needs SORTED! Powdered Hair & Body Wash, Moisturising Cream Insect Repellent, and Moisturising Cream Sunscreen SPF50. ESSENTIAL | CONVENIENT | FUNCTIONAL.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

2020 Edition of Chris Scott's Adventure Motorcycling Handbook.

"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)



Ripcord Rescue Travel Insurance.

Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.

Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.

Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!


 

What others say about HU...

"This site is the BIBLE for international bike travelers." Greg, Australia

"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK

"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia

"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA

"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada

"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa

"This is the answer to all my questions." Haydn, Australia

"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany

Lots more comments here!



Five books by Graham Field!

Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook

"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.



Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!

New to Horizons Unlimited?

New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!

Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.

Susan and Grant Johnson Read more about Grant & Susan's story

Membership - help keep us going!

Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.

You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.




All times are GMT +1. The time now is 09:00.