 |
|
20 Jan 2008
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Feb 2007
Location: Ghana
Posts: 289
|
|
I notice that you include a couple of welding rods? We are currently in the process of installing a alternator replacement welder:
http://www.zena.net/
It is being put in a L/C 79 pickup to save carrying around big welding plants in the back. So far the installation has been a bit of a hassle, but nothing too major. 200 amp welder with a continuous duty rating would be a pretty usefull thing. Maybe more the sort of thing for a support vehicle type scenario.
Of course the obvious one is also a tyre pressure guage! But I know that is really stating the obvious! Duck tape also a bit of an essential. A tyre valve tool - for removing valve cores and chasing the threads is also very small and might be usefull.
G
|
20 Jan 2008
|
 |
Gold Member
Veteran HUBBer
|
|
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
|
|
Gil, the welding rods are in there for that really dire emergency and I have to use the two batteries - not something I want to do  but when the chips are down. I've also got a couple of rods for cast iron ( can't remember which type) - these are invaluable for cracked exhaust manifolds - not ncessarily permanent but a good 'get you home' repair.
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
|
21 Jan 2008
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Sep 2007
Location: UK
Posts: 221
|
|
I've had cause to use a pop-rivet gun on every trip I've done so far, and a good selection of nuts/bolts/screws and washers has also been invaluable.
A pry bar has also come in handy a couple of times, and being a Land Rover owner, the most important tool of all - a BIG hammer 
|
21 Jan 2008
|
|
Gold Member
Veteran HUBBer
|
|
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
|
|
Quote:
Originally Posted by eightpot
I've had cause to use a pop-rivet gun on every trip I've done so far, and a good selection of nuts/bolts/screws and washers has also been invaluable.
A pry bar has also come in handy a couple of times, and being a Land Rover owner, the most important tool of all - a BIG hammer |
I wouldn't leave home without a big hammer but then I'm a blacksmith 
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
|
21 Jan 2008
|
|
Gold Member
Veteran HUBBer
|
|
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
|
|
Quote:
Originally Posted by gilghana1
I notice that you include a couple of welding rods? We are currently in the process of installing a alternator replacement welder:
Mobile DC Welding Equipment Designed for Use in Remote Locations
It is being put in a L/C 79 pickup to save carrying around big welding plants in the back. So far the installation has been a bit of a hassle, but nothing too major. 200 amp welder with a continuous duty rating would be a pretty usefull thing. Maybe more the sort of thing for a support vehicle type scenario.
Of course the obvious one is also a tyre pressure guage! But I know that is really stating the obvious! Duck tape also a bit of an essential. A tyre valve tool - for removing valve cores and chasing the threads is also very small and might be usefull.
G |
That's a very interesting bit of kit - look forward to hearing how it works out.
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
|
22 Jan 2008
|
|
Contributing Member
Veteran HUBBer
|
|
Join Date: Jul 2002
Location: Sydney, NSW, Australia
Posts: 1,362
|
|
|
Big Hammer = BMW tool No 1 - the largest hammer you have. The second biggest is BMW tool No 2.
Land anchor = spare wheel burried in a hole. Best done in sand - easier to dig. Arr yes you do need a shovel!
The gas soldering irons are good .. but you can run out of gas .. 12v you'll probably not run out of.
------------------
I count epoxy, electrical tape etc as 'consumables' .. not tools as such but more along the lines of spares. Metal epoxy is good stuff these days .. can be used on exhaust bits, fuel tanks, radiators ..
__________________
---
Regards Frank Warner
motorcycles BMW R80 G/S 1981, BMW K11LT 1993, BMW K75 G/S
|
22 Jan 2008
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Apr 2001
Location: Scotland
Posts: 775
|
|
Hello,
Has any one tried ReadWelder? Any good?
__________________
----------------
Roman (UK)
|
22 Jan 2008
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Aug 2007
Location: Sax, Spain
Posts: 901
|
|
|
reason I said gas was....
Quote:
Originally Posted by Frank Warner
Big Hammer = BMW tool No 1 - the largest hammer you have. The second biggest is BMW tool No 2.
Land anchor = spare wheel burried in a hole. Best done in sand - easier to dig. Arr yes you do need a shovel!
The gas soldering irons are good .. but you can run out of gas .. 12v you'll probably not run out of.
------------------
I count epoxy, electrical tape etc as 'consumables' .. not tools as such but more along the lines of spares. Metal epoxy is good stuff these days .. can be used on exhaust bits, fuel tanks, radiators ..
|
Frank, reason I said GAS as opposed to a 12v was, Faster heat up time... Hotter & usually Variable heat, good for heatshrink too, your NOT limited to a cable therefore can be used anywhere, even away from the vehicle.
carry a couple of Gas canisters for refilling ( about 1.50 each) and if your worried about heat affecting them, keep em in your coolbox.
Tyre OK as a land anchor but you gotta bury it DEEP. and its hard work, all the 4WD crew I used to knock about with swore by these babies...
Straight Forward Supplies Straight Forward Ground Anchor @ Straight Forward Supplies UK 4x4 Accessories
Best 99 quid inc delivery you will ever spend!
Martyn
|
22 Jan 2008
|
|
Contributing Member
Veteran HUBBer
|
|
Join Date: Jun 2005
Location: Ledbury, Herefordshire, UK
Posts: 324
|
|
Hi Roman,
Quote:
Originally Posted by Roman
|
They have a good following in the US. Obviously not as good as a proper gas MIG, but the next best thing.
__________________
Cheers,
Julian Voelcker
Overland Cruisers - Specialising in Land Cruiser preparation and servicing.
|
22 Jan 2008
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Aug 2007
Location: Sax, Spain
Posts: 901
|
|
|
exspensive for something you might never use!
Quote:
Originally Posted by Roman
|
expensive $599! and I'm suspicious as they offer new circuit boards at $79.99 and new motors at $24.99 on the first page......meaning there must be reliability issues..not something want to see on a bit of kit costing $599!
you would be better off ( IMO) having an arc welder attachment/alternator setup, that way it is ready Instantly although if your engine doesn't run....your Goosed!.... back to the twin batteries!
Martyn
|
22 Jan 2008
|
|
Registered Users
HUBB regular
|
|
Join Date: Sep 2007
Location: Ireland
Posts: 63
|
|
|
You forgot one thing!
Chris
What abour a small vice - you can pre-drill some holes in the bumber or something so it can be bolted on when needed.
Also, a stethoscope - Handy for tracking down strange noises.
Oh - and a Hamlet cigar - incase it all goes pear shaped
Also - a deep socket for the nuts on the top of shock absorbers
Oh yeah - some bailer twine
Cheers
Niallo
|
23 Jan 2008
|
|
Gold Member
Veteran HUBBer
|
|
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
|
|
Quote:
Originally Posted by Niallo
Chris
What abour a small vice - you can pre-drill some holes in the bumber or something so it can be bolted on when needed.
Also, a stethoscope - Handy for tracking down strange noises.
Oh - and a Hamlet cigar - incase it all goes pear shaped
Also - a deep socket for the nuts on the top of shock absorbers
Oh yeah - some bailer twine
Cheers
Niallo
|
Hi niallo, Yes I've got the stethoscope (a long screwdriver will do at a pinch)and a small vice but thats a good idea to pre-drill the bumper.
Intresting point about the deep sockets - not often needed but there are times when a spanner won't fit.
Bailer twine - I live on a farm 
Re: welder - does the arc welder replace the alternator or is it simply an extra bolt on?
Martyn - when the chips are down it has to be the 2 batteries - better than walking so worth carrying a few rods which would also hold up the exhaust if need be
Thanks for the input so far
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
|
23 Jan 2008
|
|
Contributing Member
Veteran HUBBer
|
|
Join Date: Jul 2002
Location: Sydney, NSW, Australia
Posts: 1,362
|
|
Quote:
Originally Posted by Martynbiker
Tyre OK as a land anchor but you gotta bury it DEEP. and its hard work, all the 4WD crew I used to knock about with swore by these babies...
|
Even a LWB 4WD runs out of room ane load ability .. Yes a spare tyre as a ground anchor is a lot of work ... but how often are you really going to use it? Most of the time there will be a passing vehicle all too willing to help.
__________________
---
Regards Frank Warner
motorcycles BMW R80 G/S 1981, BMW K11LT 1993, BMW K75 G/S
|
23 Jan 2008
|
|
Gold Member
Veteran HUBBer
|
|
Join Date: Mar 2007
Location: south Cumbria
Posts: 364
|
|
One intersting tip on the ground anchor is to fill/bury a large builders sack or a parachute. Much lighter than a ground anchor but a lot more shoveling
I have a ply board in the car to sleep on but I'm sure with a few holes in each corner, 2 straps it would work as an anchor.
a good rule of thumb is :- 1 cu m h2o = 1 tonne - sand is a bit heavier but you get the idea 
__________________
Chris
-----------------
"Never have a stupid argument with an idiot - he gets a lot more practice than you"
there I go again
not too hard really
Last edited by silver G; 23 Jan 2008 at 02:08.
|
18 Oct 2008
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Feb 2007
Location: Ghana
Posts: 289
|
|
|
On board welding kit
Well, I said the installation seemed to be smooth, but in reality we ordered some wrong parts, Ghana customs went on lunch and everything slowed right down as it sometimes does with projects here! The welding alternator is from
Mobile DC Welding Equipment Designed for Use in Remote Locations
It has been in use for one month now, every single day out in the forest doing serious welding - CAT undercarriage etc. This is not light or hobby type use and neither are the operators. So far so good, the quality seems really good and our welders reckon it is one of the best welding machines of ANY type they have used. It could make a very useful thing to have under the bonnet. To set it up it is simply a question of swapping a big anderson plug connection to weld instead of charge.
Gil
|
|
Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Next HU Events
ALL Dates subject to change.
2025 Confirmed Events:
- Virginia: April 24-27 2025
- Queensland is back! May 2-4 2025
- Germany Summer: May 29-June 1 2025
- CanWest: July 10-13 2025
- Switzerland: Date TBC
- Ecuador: Date TBC
- Romania: Date TBC
- Austria: Sept. 11-14
- California: September 18-21
- France: September 19-21 2025
- Germany Autumn: Oct 30-Nov 2 2025
Add yourself to the Updates List for each event!
Questions about an event? Ask here
See all event details
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...
2020 Edition of Chris Scott's Adventure Motorcycling Handbook.
"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)
Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.
Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.
Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!
What others say about HU...
"This site is the BIBLE for international bike travelers." Greg, Australia
"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK
"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia
"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA
"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada
"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa
"This is the answer to all my questions." Haydn, Australia
"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany
Lots more comments here!
Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook
"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.
Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!
New to Horizons Unlimited?
New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!
Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.
Read more about Grant & Susan's story
Membership - help keep us going!
Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.
You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.
|
|
|
helps answer the question - Why Go? Inspirational stories by veteran travellers Greg Frazier (5 times RTW), Peter and Kay Forwood (193 countries), Tiffany Coates (Mongolia Mayhem) and Rene Cormier (University of Gravel Roads).
Get Ready! covers planning, paperwork, medical and many other topics! "Inspirational and Awesome!" See the trailer here!
What stuff do I need - riding gear, clothing, camping gear, first aid kit, tires, maps and GPS? What don't I need? How do I pack it all in? Lots of opinions from over 150 travellers!
break down language barriers, overcome culture shock, ship the bike and deal with breakdowns and emergencies."Just makes me want to pack up and go!" See the trailer here!
Grant demystifies the black art of Tire Changing and Repair to help you STAY on the road! "Very informative and practical." See the trailer here!
Ladies on the Loose! For the first time ever, a motorcycle travel DVD made for women, by women! These intrepid women share their tips to help you plan your own motorcycle adventure. They also answer the women-only questions, and entertain you with amazing tales from the road! Presented by Lois Pryce, veteran solo traveller through South America and Africa and author of 'Lois on the Loose', and 'Red Tape and White Knuckles.'
Cotton or synth sweat-wicking t-shirts with the cool Horizons Unlimited graphic on the front and a snappy slogan (changing every year) on the back.
Show your route on your panniers. Great conversation starter when you meet people on the road!
Motorcycle and travel books to inspire and inform you!
The definitive guide to planning your motorcycle adventure! This insanely ambitious 2-year project has produced an informative and entertaining 5-part, 18 hour video series. "The ultimate round the world rider's how-to!" MCN UK.
Linear Mode
