|
|
31 Jul 2009
|
Registered Users
Veteran HUBBer
|
|
Join Date: Jun 2009
Posts: 168
|
|
clinking sound in engine xt600e 2001
Im pretty sure i can hear some kind of clinking sound in the engine/cylinder, is this "dangerous"? what could it be? If i record the sound will you guys be able to recognize it you think?
|
1 Aug 2009
|
Registered Users
Veteran HUBBer
|
|
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
|
|
Try us =)
Is it both with cold and warm motor?
It might just be the valves that needs to be adjustet
|
17 Jan 2010
|
Registered Users
Veteran HUBBer
|
|
Join Date: Jun 2009
Posts: 168
|
|
Quote:
Originally Posted by Jens Eskildsen
Try us =)
Is it both with cold and warm motor?
It might just be the valves that needs to be adjustet
|
A very late reply here but I just uploaded the video I took this summer onto youtube. The video is upside down but hope you can hear something..
YouTube - xt 600 E 2001 strange engine sound?
btw. i think it gets better when its warmed up..but the engine feels very "plush", I hope its just the valves.
|
17 Jan 2010
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Dec 2009
Location: Brisbane, Australia
Posts: 133
|
|
I've heard that when the later models (4PT) were made the tools that made them in the factory were'nt as sharp due to having made a bazillion of these engines in there lifetime and as such the tolerances arent as fine. I asked a Yamaha dealer about this and he confirmed it. It doesnt, however, mean anything bad, so I've been told. Mine makes a strange sound when cold, but when it gets warmed up it goes away.
|
17 Jan 2010
|
Registered Users
HUBB regular
|
|
Join Date: Aug 2007
Location: Croatia
Posts: 61
|
|
Maybe it's cam chain? Here is how my cam chain sound like when it was ready for replacing.
YouTube - XT600E valve sound
|
17 Jan 2010
|
Registered Users
New on the HUBB
|
|
Join Date: Dec 2009
Location: england
Posts: 9
|
|
It does sound very much like your valves need adjusting , Its not very expensive to have done or you can even do it yourself , Better still take it to your local bike shop and let him have a listen.
|
17 Jan 2010
|
|
Contributing Member
Veteran HUBBer
|
|
Join Date: Jul 2005
Location: Wirral, England.
Posts: 5,673
|
|
My 2003 XT600E made the same sound at idle with 4000 miles and in PERFECT balance and spec !!
These engines are OLD design and arnt quiet..
By all means, check your valves... You should be anyway !!
It sounds very healthy when you rev it..
__________________
Did some trips.
Rode some bikes.
Fix them for a living.
Can't say anymore.
|
19 Jan 2010
|
|
Registered Users
HUBB regular
|
|
Join Date: Aug 2007
Location: Whitchurch
Posts: 79
|
|
What sort of mileage has the bike covered?
Do you know any of the bikes history? (thrashed/ 1 old nun owner)?
Maybe a bit of piston slap?
Andy
|
19 Jan 2010
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
|
|
valves! check gap :P
also... my camshaft chain gave up with only 30 000 km on the clock... I know.. i push too hard too often...
anyway... check the chain and the timing if you can!
Vando
|
3 Apr 2011
|
Registered Users
Veteran HUBBer
|
|
Join Date: Jun 2009
Posts: 168
|
|
Old thread but I took a new video today, not sure you can hear anything, starts easy runs good but the throttle response is slow. If you could look at the rpm needle and see if its normal? The part where i film the rpm needle i give 100% gas at that moment and it revs kinda slow?
YouTube - xt600 E 2001 strange engine sound? #2
Sorry for bothering with this topic over and over hehe, i just want to be sure shes fine
|
4 Apr 2011
|
Registered Users
Veteran HUBBer
|
|
Join Date: Apr 2003
Location: Manchester UK
Posts: 235
|
|
Sounds like your mixture may be a bit rich. (burbling rich)
Check float level and if that's fine try the air pilot screw. (tighten to close counting the exact amount of turns in so you can always return it back to your starting point. Return to your starting point and perform the following) Turn in 1/16th at a time until the revs start to climb. when the revs start to drop turn back out till max revs reached and then a further 1/8th turn out (safer to be slightly rich).
|
5 Apr 2011
|
Registered Users
Veteran HUBBer
|
|
Join Date: Dec 2008
Location: Denmark
Posts: 1,417
|
|
Idle is a bit low, I just think the bike isnt fully warm, that will cause the enginestall, and making it a bit harder for the engine to rev. I really wouldn't bother with carbwork if you dont experience surging or other stuff.
But come on, its been 2 years, if it bothers you that much, either strip it apart and rebuild, or ride and see if it grenades on you.
It doesnt sound too bad to me, but its hard to hear on video.
Theres a big nut, I think its hehind the clutch, I've heard a couple of stories where the nut got loose, and the bike starting making noice. Might be a seasy check, only cost you a gasket to check it. And a clutch-holder-tool to removed the clutch if you need to tighten the bolt.
Is there enough oil on? If you run it low it will start to make more noise. Check the valves also, the make clicking sounds when loose aswell.
Hope you get it sortet
Heres my bike idling/reving at 75.000km:
YouTube - Yamaha xt600e 2003, with 75.000km
Ive done over 10.000km since with no problem.
|
12 Apr 2011
|
Registered Users
Veteran HUBBer
|
|
Join Date: Dec 2005
Location: Kandahar Afghanistan
Posts: 160
|
|
Mine was ticking from the top end very loud when cold, the bike shop had put 10w 40 oil in it so put in 20w50 now nice and quiet gears no longer clunk and it rins so much smoother no surging at 3-4000 rpm.
|
13 Apr 2011
|
|
Registered Users
Veteran HUBBer
|
|
Join Date: Sep 2007
Location: XXX<-Portugal->Azores->Santa Maria (island)
Posts: 1,544
|
|
the bike is fine!
You just need to set the idle RPM's a bit higher to at least 1300/1400 as this will cause the bike to REV a lot slower!
I've read this before but I can't remember where..
It has something to do with the inertia of the engine which causes "underpressure" to suck in fuel in.
Also, check your sparkplug gap be sure to make it from 0.6 to 0.9mm I got 0.7mm on mine and the sparkplug color changed from way overrich to slightly better color(the black sooth pratically dissapeared).
Vando
|
14 Apr 2011
|
Registered Users
Veteran HUBBer
|
|
Join Date: Jun 2009
Posts: 168
|
|
Is the air pilot screw accessible from outside the carb or do i have to take it off?
Quote:
Originally Posted by bruken
Sounds like your mixture may be a bit rich. (burbling rich)
Check float level and if that's fine try the air pilot screw. (tighten to close counting the exact amount of turns in so you can always return it back to your starting point. Return to your starting point and perform the following) Turn in 1/16th at a time until the revs start to climb. when the revs start to drop turn back out till max revs reached and then a further 1/8th turn out (safer to be slightly rich).
|
|
Currently Active Users Viewing This Thread: 1 (0 Registered Users and/or Members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
Check the RAW segments; Grant, your HU host is on every month!
Episodes below to listen to while you, err, pretend to do something or other...
2020 Edition of Chris Scott's Adventure Motorcycling Handbook.
"Ultimate global guide for red-blooded bikers planning overseas exploration. Covers choice & preparation of best bike, shipping overseas, baggage design, riding techniques, travel health, visas, documentation, safety and useful addresses." Recommended. (Grant)
Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.
Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.
Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes!
What others say about HU...
"This site is the BIBLE for international bike travelers." Greg, Australia
"Thank you! The web site, The travels, The insight, The inspiration, Everything, just thanks." Colin, UK
"My friend and I are planning a trip from Singapore to England... We found (the HU) site invaluable as an aid to planning and have based a lot of our purchases (bikes, riding gear, etc.) on what we have learned from this site." Phil, Australia
"I for one always had an adventurous spirit, but you and Susan lit the fire for my trip and I'll be forever grateful for what you two do to inspire others to just do it." Brent, USA
"Your website is a mecca of valuable information and the (video) series is informative, entertaining, and inspiring!" Jennifer, Canada
"Your worldwide organisation and events are the Go To places to for all serious touring and aspiring touring bikers." Trevor, South Africa
"This is the answer to all my questions." Haydn, Australia
"Keep going the excellent work you are doing for Horizons Unlimited - I love it!" Thomas, Germany
Lots more comments here!
Diaries of a compulsive traveller
by Graham Field
Book, eBook, Audiobook
"A compelling, honest, inspiring and entertaining writing style with a built-in feel-good factor" Get them NOW from the authors' website and Amazon.com, Amazon.ca, Amazon.co.uk.
Back Road Map Books and Backroad GPS Maps for all of Canada - a must have!
New to Horizons Unlimited?
New to motorcycle travelling? New to the HU site? Confused? Too many options? It's really very simple - just 4 easy steps!
Horizons Unlimited was founded in 1997 by Grant and Susan Johnson following their journey around the world on a BMW R80G/S.
Read more about Grant & Susan's story
Membership - help keep us going!
Horizons Unlimited is not a big multi-national company, just two people who love motorcycle travel and have grown what started as a hobby in 1997 into a full time job (usually 8-10 hours per day and 7 days a week) and a labour of love. To keep it going and a roof over our heads, we run events all over the world with the help of volunteers; we sell inspirational and informative DVDs; we have a few selected advertisers; and we make a small amount from memberships.
You don't have to be a Member to come to an HU meeting, access the website, or ask questions on the HUBB. What you get for your membership contribution is our sincere gratitude, good karma and knowing that you're helping to keep the motorcycle travel dream alive. Contributing Members and Gold Members do get additional features on the HUBB. Here's a list of all the Member benefits on the HUBB.
|
|
|