BMW R models 1970-1985 Engine Technical specs
Engine | Type: | Air - cooled horizontally - opposed transverse twin, with pushrod operated overhead valves | ||
Dimensions | Bore | Stroke | Capacity - Actual | |
R45 | 70.0mm (2.76") | 61.5mm (2.42") | 473.1cc (28.86 cu in) | |
R50 | 67.0mm (2.64") | 70.6mm (2.78") | 497.6cc (30.35 cu in) | |
R60 | 73.5mm (2.89") | 70.6mm (2.78") | 598.8cc (36.53 cu in) | |
R65, R65LS | 82.0mm (3.23") | 61.5mm (2.42") | 649.2cc (39.60 cu in) | |
R75 | 82.0mm (3.23") | 70.6mm (2.78") | 745.3cc (45.46 cu in) | |
All 800cc models | 84.8mm (3.34") | 70.6mm (2.78") | 797.1cc (48.62 cu in) | |
R90/6, R90S | 90.0mm (3.54") | 70.6mm (2.78") | 897.8cc (54.77 cu in) | |
All 1000cc models | 94.0mm (3.70") | 70.6mm (2.78") | 979.4cc (59.74 cu in) | |
Compression ratio(standard values quoted, some machines may have been fitted with compression plates to reduce compression ratio from standard) | ||||
R45 | 9.2 : 1 | |||
R50 | 8.6 : 1 | |||
R60 | 9.2 : 1 | |||
R65, R65LS | 9.2 : 1 | |||
R75 | 9.0 : 1 | |||
R80/7 - 40 kw version | 9.2 : 1 | |||
R80/7 - 37 kw version, all other 800cc models | 8.2 : 1 | |||
R90/6 | 9.0 : 1 | |||
R90S | 9.5 : 1 | |||
R100/7 | 9.0 : 1 | |||
R100 (UK) | 8.2 : 1 | |||
All other 1000cc models* | 9.5 : 1 | |||
| ||||
Recommended engine speeds - rpm: | ||||
| Idle | Max. permissible continuous | Max. permissible | |
R45 R65 R65LS | 800 - 1100 | 7300 | 7650 | |
R50 R60/5 R60/6 R75/5 R75/6 R90/6 | 600 - 800 | 6500 | 7000 | |
R60/7 | 800 - 1100 | 6500 | 7200 | |
R75/7 | 800 - 1100 | 6500 | 7400 | |
All 800cc models | 800 - 1100 | 7200 | 7400 | |
R90S | 600 - 800 | 7000 | 7300 | |
R100/7 | 800 - 1100 | 6800 | 7400 | |
All other 1000cc models - UK - all R100T R100S 1977,78 - US - all except below | 800 - 1100 | 7000 | 7400 | |
All other 1000cc models - UK - all except those above - US - R100RS 1977 | 800 - 1100 | 7200 | 7400 | |
Claimed engine output - DIN: |
| Max. power (kw/hp @ rpm) | Max. torque (Nm/lbf ft @ rpm) | |
R45 | 26/35 @ 7250 | 37.4/27.6 @ 5500 | ||
R50 | 24/32 @ 6400 | 38.3/28.3 @ 5000 | ||
R60 | 29/40 @ 6400 | 48.1/35.5 @ 5000 | ||
R65 1978 - 80 models* | 33/45 @ 7250 | 50.0/36.9 @ 5500 | ||
R65 1981 on models, R65LS* | 37/50 @ 7250 | 52.3/38.6 @ 6500 | ||
R75 | 37/50 @ 6200 | 58.8/43.4 @ 5000 | ||
R80/7 - high comp. version | 40/55 @ 7000 | 62.5/46.1 @ 5500 | ||
R80/7 - low comp. version | 37/50 @ 7250 | 56.6/41.8 @ 5500 | ||
R80G/S R80ST* | 37/50 @ 6500 | 56.7/41.9 @ 5000 | ||
R80RT 1983, 84 models* | 37/50 @ 6500 | 59.0/43.5 @ 3500 | ||
R80, R80RT 85 on models* | 37/50 @ 6500 | 58.0/42.8 @ 4000 | ||
R90/6 | 44/60 @ 6500 | 73.0/53.9 @ 5500 | ||
R90S | 49/67 @ 7000 | 76.0/56.1 @ 5500 | ||
R100/7 | 44/60 @ 6500 | 73.5/54.2 @ 4000 | ||
R100T - US* | 44/60 @ 6500 | 74.6/55.1 @ 5500 | ||
R100T - UK, R100S - UK '77, '78 R100S - US, R100RS - US '78, '79, R100RT - US* | 48/65 @ 6600 | 75.0/55.4 @ 5500 | ||
R100 - UK | 49/67 @ 7000 | 72.0/53.1 @ 5500 | ||
R100S - UK '79, '80, R100RS - UK '77 - '80, R100RT - UK '79, '80 R100RS - US '77* | 51/70 @ 7250 | 76.0/56.1 @ 5500 | ||
R100CS R100RS R100RT - UK models '81 on* | 51/70 @ 7000 | 76.0/56.1 @ 6000 | ||
| ||||
Direction of engine rotation | clockwise, looking from front of machine | |||
Compression pressure | R80G/S R80ST R80RT R80 '85 on | All other models | ||
Good | over 9.0bar (131psi) | over 10.0bar (145psi) | ||
Normal | 7.5 - 9.0bar (109 - 131psi) | 8.5 - 10.0bar (123 - 145psi) | ||
Poor | below 7.5bar (109psi) | below 8.5bar (123psi) | ||
Valve clearances - engine cold | Normal | First 1000km (600m) | ||
Inlet | Exhaust | Inlet | Exhaust | |
/5,/6 | 0.15mm (.006") | 0.20mm (.008") | N/Av | N/Av |
/7, R80G/S, R80ST, R80RT '83 - 84 | 0.10mm (.004") | 0.15mm (.006") | 0.15mm (.006") | 0.20mm (.008") |
R45, R65, R65LS, R80, R80RT '85 on | 0.10mm (.004") | 0.20mm (.008") | 0.25mm (.010") | |
Valve timing | with 2.0mm (.08") valve clearance, tolerance of + - 2.5 degrees. | |||
R50/5 R60/5 R60/6 up to 1975 | R60/6 '76 R60/7 '77 | R60/7 '78 | ||
Inlet opens | 40 deg ATDC | TDC | 6 deg BTDC | |
Inlet closes | 40 deg ABDC | 40 deg ABDC | 34 deg ABDC | |
Exhaust opens | 40 deg BBDC | 40 deg BBDC | 46 deg BBDC | |
Exhaust closes | 40 deg BTDC | TDC | 6 deg BTDC | |
All R75 & R90, R100/7 R100S R100RS '77 | R80/7 R100/7 R100S R100RS '78 | All other models | ||
Inlet opens | 10 deg BTDC | 16 deg BTDC | 16 deg BTDC | |
Inlet closes | 50 deg ABDC | 44 deg ABDC | 44 deg ABDC | |
Exhaust opens | 50 deg BBDC | 56 deg BBDC | 56 deg BBDC | |
Exhaust closes | 10 deg BTDC | 4 deg BTDC | 4 deg ATDC | |
Valves | ||||
Head diameter: | Inlet | Exhaust | ||
R45 R50 | 34mm (1.34") | 32mm (1.26") | ||
R60 R65 up to '80 | 38mm (1.50") | 34mm (1.34") | ||
R65 '81 on, R65LS | 40mm (1.58") | 36mm (1.42") | ||
R75, all 800cc models | 42mm (1.65") | 38mm (1.50") | ||
R90/6 R90S R100/7 | 42mm (1.65") | 40mm (1.58") | ||
All other 1000cc models | 44mm (1.73") | 40mm (1.58") | ||
Head rim minimum thickness: | ||||
/5 /6 /7 | 1.0mm (0.0394") | 1.0mm (0.0394") | ||
R80G/S R80ST R80RT '83 - '84 | 0.8mm (0.0315") | 0.8mm (0.0315") | ||
R45 R65 R65LS | 1.0 - 1.5mm (0.0394 - 0.0591") | 1.0 - 1.2mm (0.0394 - 0.0472") | ||
Head maximum runout: | ||||
/5 /6 /7 | 0.025mm (0.0010") | 0.025mm (0.0010") | ||
R80G/S R80ST R80RT '83 - 84 | 0.020mm (0.0008") | 0.020mm (0.0008") | ||
Overall length: | ||||
R50/5 | 102.6 - 103.0mm | 102.1 - 102.5mm | ||
(4.0394 - 4.0551") | (4.0197 - 4.0354") | |||
R45 R65 R65LS | 98.8 - 100.2mm | 99.1 - 99.5mm | ||
(3.8898 - 3.9449") | (3.9016 - 3.9173") | |||
R60/5 R60/6 | 98.2 - 98.5mm | 97.2 - 97.5mm | ||
(3.8661 - 3.8780") | (3.8268 - 3.8386") | |||
R60/7 | 99.2 - 99.5mm | 98.2 - 98.5mm | ||
(3.9055 - 3.9173") | (3.8661 - 3.8780") | |||
All other models | 98.4 - 98.8mm | 98.4 - 98.8mm | ||
(3.8740 - 3.8898") | (3.8740 - 3.8898") | |||
Valve Guides | ||||
Length overall: | ||||
/5 /6 except R90S | 54mm (2.1260") | |||
R90S, /7 | 48mm (1.8898") | |||
R45 R65 R65LS | 45mm (1.7717") | |||
R80G/S R80ST R80RT '83 - '84 | 44mm (1.7323") | |||
Outside diameter: | ||||
/5 /6 /7 R80G/S R80ST R80RT '83 - 84 | 14.050 - 14.061mm (0.5532 - 0.5536") | |||
R45 R65 R65LS | 14mm (0.5512") | |||
Inside diameter: | ||||
/5 /6 /7 | 8mm (0.3150") | |||
R45 R65 R65LS | 7mm (0.2756") | |||
R80G/S R80ST R80RT '83 - 84 | 8.000 - 8.015mm (0.3150 - 0.3156") | |||
Bore in cylinder head: | ||||
/5 /6 /7 R45 R65 R65LS | 14mm (0.5512") | |||
R80G/S R80ST R80RT '83 - 84 | 14.000 - 14.018mm (0.5512 - 0.5519") | |||
Interference fit in cylinder head: | ||||
/5 /6 /7 | 0.032 - 0.061mm (0.0013 - 0.0024") | |||
All other models | N/Av | |||
Oversizes available | 0.1 & 0.2mm (0.004 & 0.008") | |||
Valve stem / guide standard clearance: | Inlet | Exhaust | ||
R50/5 | 0.040 - 0.070mm | 0.050 - 0.080mm | ||
(0.0016 - 0.0028") | (0.0020 - 0.0032") | |||
R45 R65 R65LS | 0.025 - 0.055mm | 0.040 - 0.070mm | ||
(0.0010 - 0.0022") | (0.0016 - 0.0028") | |||
R60 | 0.050 - 0.080mm | 0.065 - 0.095mm | ||
(0.0020 - 0.0032") | (0.0026 - 0.0037") | |||
All other models | 0.050 - 0.080mm | 0.050 - 0.080mm | ||
(0.0020 - 0.0032") | (0.0020 - 0.0032") | |||
Inlet and exhaust valve stem / guide max. permissible clearance - measured at top of guide: | ||||
R45 R65 R65LS | 0.10mm (0.0039") | |||
All other models | 0.15mm (0.0059") | |||
Valve seats | ||||
Outside diameter: | Inlet | Exhaust | ||
R50/5 | 36.175 - 36.200mm | 36.140 - 36.150mm | ||
(1.4242 - 1.4252") | (1.4228 - 1.4232") | |||
R45 | 36.2mm (1.4252") | 36.2mm (1.4252") | ||
R60 | 39.175 - 39.200mm | 39.175 - 39.200mm | ||
(1.5423 - 1.5433") | (1.5423 - 1.5433") | |||
R65 R65LS | 39.2mm (1.5433") | 39.2mm (1.5433") | ||
R75/5 | 43.175 - 43.200mm | 43.140 - 43.150mm | ||
(1.6998 - 1.7008") | (1.6984 - 1.6988") | |||
R75/6 R90/6 R90S | 43.175 - 43.200mm | 43.175 - 43.200mm | ||
(1.6998 - 1.7008") | (1.6998 - 1.7008") | |||
R75/7 R80/7 R100/7 | 43.175 - 43.200m | 43.134 - 43.200mm | ||
(1.6998 - 1.7008") | (1.6982 - 1.7008") | |||
R80G/S R80ST R80RT '83 - 84 | 43.175 - 43.200m | 43.134 - 43.150mm | ||
(1.6998 - 1.7008") | (1.6982 - 1.6988") | |||
All other 1000cc models | 45.175 - 45.200mm | 45.175 - 45.200mm | ||
(1.7785 - 1.7795") | (1.7785 - 1.7795") | |||
Bore in cylinder head - inlet and exhaust: | ||||
R50/5 | 36.00 - 36.025mm (1.4173 - 1.4183") | |||
R45 | 36mm (1.4173") | |||
R60 | 39.00 - 39.025mm (1.5354 - 1.5364") | |||
R65, R65LS | 39mm (1.5354") | |||
All 745cc 800cc 900cc, R100/7 | 43.000 - 43.025mm (1.6929 - 1.6939") | |||
All other 1000cc models | 45.000 - 45.025mm (1.7717 - 1.7727") | |||
Interference fit in cylinder head: | Inlet | Exhaust | ||
R50/5 R75/5 | 0.150 - 0.200mm (0.0059 - 0.0079") | 0.115 - 0.150mm (0.0045 - 0.0059") | ||
R45 R65 R65LS | N/Av | N/Av | ||
R75/7 R80/7 R100/7 R80G/S R80ST | ||||
R80RT '83 - '84 | 0.150 - 0.200mm (0.0059 - 0.0079") | 0.109 - 0.150mm (0.0043 - 0.0059") | ||
All other models | 0.150 - 0.200mm (0.0059 - 0.0079") | 0.150 - 0.200mm (0.0059 - 0.0079") | ||
Seat angle: | ||||
Main seating face | 45 deg | |||
At combustion chamber | 15 deg | |||
At inlet/exhaust port | 75 deg | |||
Seat width: | ||||
Inlet | 1.5mm (0.0591") | |||
Exhaust | 2.0mm (0.0787") | |||
Seat oversizes available | 0.2 0.4mm (0.0079 0.0168") | |||
Valve springs | ||||
Wire thickness | 4.25mm (0.1673") | |||
Spring free length - approx: | ||||
Blue or green code | 43.5mm (1.7126") | |||
Brown code | 46.0mm (1.811") | |||
Spring force at test length: | ||||
At 37.6mm (1.4803") | 27.84 - 30.16 kp (61.30 - 66.5 lb) | |||
At 28.5mm (1.1221") | 70.00 - 72.80 kp (154.30 - 160.5 lb) | |||
Rocker gear | ||||
Arm ID - /5 | 18.032 - 18.059mm (0.7099 - 0.7110") | |||
Bush OD - /5 | 18.012 - 18.030mm (0.7091 - 0.7098") | |||
Arm/bush clearance - /5 | 0.002 - 0.047mm (0.00008 - 0.00185") | |||
Bush ID /5 | 14.532 - 14.559mm (0.5721 - 0.5732") | |||
Shaft OD /5 | 14.512 - 14.530mm (0.5713 - 0.5720") | |||
Bush / shaft clearance /5 | 0.002 - 0.047mm (0.00008 - 0.00185") | |||
Arm axial float: | ||||
R80 R80RT 1985 | 0.03 - 0.07mm (0.0012 - 0.0028") | |||
All other models | Nil, but arm must be free to move | |||
Camshaft drive chain | ||||
Type: | ||||
/5 /6 /7 up to 1978 | Duplex roller chain | |||
All other models | Single row chain | |||
Size | 3/8 x 7/32" | |||
Number of links | 50 | |||
Camshaft | ||||
Front (alternator end) bearing bore | 40.000 - 40.039mm (1.5748 - 1.5763") | |||
Front flange bearing OD | 39.984 - 40.000mm (1.5742 - 1.5748") | |||
Front flange bearing ID | 25.000 - 25.013mm (0.9843 - 0.9848") | |||
Camshaft front bearing journal OD | 24.967 - 24.980mm (0.9830 - 0.9835") | |||
Camshaft radial clearance - at front bearing | 0.020 - 0.046mm (0.0008 - 0.0018") | |||
Rear (flywheel end) bearing bore | 24.000 - 24.021mm (0.9449 - 0.9457") | |||
Camshaft rear bearing journal OD | 23.967 - 23.980mm (0.9436 - 0.9441") | |||
Camshart radial clearance - at rear bearing | 0.020 - 0.054mm (0.0008 - 0.0021") | |||
Camshaft end float | 0.080 - 0.120mm (0.0032 - 0.0047") | |||
Base circle | 28mm (1.1024") | |||
Cam lift: | ||||
R50/5 R60 | 6.198mm (0.2440") | |||
All other models | 6.756mm (0.2660") | |||
Maximum permissible runout of ATU shaft - /5 /6 /7 up to '78 | 0.02mm (0.0008") | |||
Cam followers and pushrods | ||||
OD | 21.955 - 21.975mm (0.8644 - 0.8652") | |||
Crankcase ID | 21.985 - 22.006mm (0.8656 - 0.8664") | |||
Follower / crankcase clearance: | ||||
Standard | 0.010 - 0.051mm (0.0004 - 0.0020") | |||
Service limit | 0.075mm (0.0030") | |||
Pushrod length: | ||||
R45 R65 R65LS /5 /6 up to '75 | N/Av | |||
All other models | 274.7 - 275.3mm (10.8149 - 10.8386") | |||
Crankshaft and main bearings | ||||
Journal dimensions | Basically the same, but tolerances vary according to model and year. | |||
Main bearing bushes dimensions and radial clearances. | Selective fit depending on journal | |||
Main bearing journal/bush clearance: | ||||
R45 (UK), R65 (UK), R65LS (UK), all /5 /6 /7 | 0.035 - 0.065mm (0.0014 - 0.0025") | |||
/7 '81 on, R80G/S, R80ST, R65 (US), R65LS (US) - red size bush | 0.017 - 0.066mm (0.0007 - 0.0026") | |||
/7 '81 on, R80G/S, R80ST, R65 (US), R65LS (US) - blue size bush | 0.019 - 0.067mm (0.0008 - 0.0026") | |||
Crankshaft regrind stages: | ||||
1st | 0.25mm (0.0100") | |||
2nd | 0.50mm (0.0200") | |||
3rd | 0.75mm (0.0300") | |||
Max. runout - at front main bearing journal | 0.02mm (0.0008") | |||
Max. lateral runout at flywheel | 0.10mm (0.0008") | |||
Crankshaft standard endfloat | 0.08 - 0.15mm (0.0032 - 0.0059") | |||
Thrust washer thickness: | ||||
Standard - red | 2.483 - 2.530mm (0.0978 - 0.0996") | |||
Standard - blue | 2.530 - 2.578mm (0.0996 - 0.1015") | |||
Standard - green | 2.578 - 2.626mm (0.1015 - 0.1034") | |||
Standard - yellow | 2.626 - 2.673mm (0.1034 - 0.1052") | |||
Wear limit - all | minus 0.20mm (0.0079") | |||
Connecting rods and bearings | ||||
Crankpin standard OD | 47.975 - 47.991mm (1.8888 - 1.8894") | |||
Crankpin regrind stages: | ||||
1st | 0.25mm (0.0100") | |||
2nd | 0.50mm (0.0200") | |||
3rd | 0.75mm (0.0300") | |||
Connecting rod big - end ID - less bearing shells: | ||||
/5, /6, /7 1977 | 52.000 - 52.010mm (2.0472 - 2.0476") | |||
All other models | 52.000 - 52.015mm (2.0472 - 2.0478") | |||
Con. rod radial clearance | 0.023 - 0.069mm (0.0009 - 0.0027") | |||
Con. rod big - end width | 21.883 - 21.935mm (0.8615 - 0.8636") | |||
Crankpin width | 22.065 - 22.149mm (0.8657 - 0.8720") | |||
Con. rod axial clearance (endfloat): | ||||
Standard | 0.130 - 0.266mm (0.0051 - 0.105") | |||
Max. permissible | 0.320mm (0.0126") | |||
Max. weight difference between con. rods: | ||||
/5, /6 | 6 grams (0.2116 oz) | |||
/7, R45, R65, R65LS | 3 grams (0.1058 oz) | |||
R80G/S, R80ST | 2 grams (0.0705 oz) | |||
Con. rod small - end ID - less bush | 24.000 - 24.021mm (0.9449 - 0.9457") | |||
Small - end bush OD | 24.060 - 24.100mm (0.9472 - 0.9488") | |||
Small - end bush ID: | ||||
Standard | 22.015 - 22.020mm (0.8667 - 0.8669") | |||
Max. permissible | 22.040mm (0.8677") | |||
Gudgeon pin/small - end bush clearance: | ||||
/5,/6,/7 up to '80 - white coded pin | 0.015 - 0.023mm (0.0006 - 0.0009") | |||
/5,/6,/7 up to '80 - black coded pin | 0.018 - 0.026mm (0.0007 - 0.0010") | |||
/7 '81 on, R80G/S, R80ST | 0.015 - 0.024mm (0.0006 - 0.0009") | |||
R45, R65, R65LS | 0.015 - 0.025mm (0.0006 - 0.0009") | |||
Gudgeon pin OD: | ||||
/5,/6,/7 up to '80 - white coded pin | 21.997 - 22.000mm (0.8660 - 0.8661") | |||
/5,/6,/7 up to '80 - black coded pin | 21.994 - 21.997mm (0.8659 - 0.8660") | |||
/7 '81 on, R80G/S, R80ST | 21.996 - 22.000mm (0.8659 - 0.8661") | |||
R45, R65, R65LS | 21.995 - 22.000mm (0.8659 - 0.8661") | |||
Gudgeon pin bore ID - in piston: | ||||
/5,/6,/7 up to '80 - white code (W stamped in piston crown) | 22.000 - 22.003mm (0.8661 - 0.8662") | |||
/5,/6,/7 up to '80 - black code (S stamped in piston crown) | 21.997 - 22.000mm (0.8660 - 0.8661") | |||
/7 '81 on, R80G/S, R80ST | 22.000 - 22.004mm (0.8661 - 0.8663") | |||
R45 | 22.002 - 22.007mm (0.8662 - 0.8664") | |||
R65, R65LS | 22.005 - 22.010mm (0.8663 - 0.8665") | |||
Gudgeon pin/piston clearance: | ||||
/5,/6,/7 up to '80 | 0.000 - 0.006mm (0.0000 - 0.0002") | |||
/7 '81 on, R80G/S, R80ST | 0.000 - 0.008mm (0.0000 - 0.0003") | |||
R45 | 0.002 - 0.012mm (0.0001 - 0.0005") | |||
R65, R65LS | 0.005 - 0.015mm (0.0002 - 0.0006") | |||
Cylinders | ||||
Type: | ||||
All models up to 1980 finned jacket by 'Al-Fin' process | Cast iron sleeve joined to aluminium alloy | |||
R45, R65, R65LS '81 on | Aluminium alloy barrel with 'Nikasil' plated bore | |||
1000cc and 800cc, '81 on | Aluminium alloy barrel with 'Galnikal' plated bore | |||
Cylinder standard bore ID - at specified bore size code: | ||||
A | B | C | ||
R50/5 | 67.000mm | 67.010mm | 67.020mm | |
(2.7368") | (2.6382") | (2.6386") | ||
R45 | 69.995 - 70.005mm | 70.005 - 70.015mm | 70.015 - 70.025mm | |
(2.7557 - 2.7561") (2.7561 - 2.7565") (2.7565 - 2.7569") | ||||
R60/5, R60/6 | 73.500mm | 73.510mm | 73.520mm | |
(2.8937") | (2.8941") | (2.8945") | ||
R60/7 | 73.500 - 73.510mm | 73.510 - 73.520mm | 73.520 - 73.530mm | |
(2.8937 - 2.8941") (2.8941 - 2.8945") (2.8945 - 2.8949") | ||||
R65, R65LS | 81.995 - 82.005mm | 82.005 - 82.015mm | 82.015 - 82.025mm | |
(3.2281 - 3.2285") (3.2285 - 3.2289") (3.2289 - 3.2293") | ||||
R75/5, R75/6 | 82.000mm (3.2283") | 82.010mm (3.2287") | 82.020mm (3.2291") | |
R75/7 | 82.005 - 82.015mm (3.2285 - 3.2289") | 82.015 - 82.025mm (3.2289 - 3.2293") | 82.025 - 82.035mm (3.2293 - 3.2297") | |
All 800cc models | 84.795 - 84.805mm (3.3384 - 3.3388") | 84.805 - 84.815mm (3.3388 - 3.3392") | 84.815 - 84.825mm (3.3392 - 3.3396") | |
R90/6, R90S | 90.000mm (3.5433") | 90.010mm (3.5437") | 90.020mm (3.5441") | |
All 1000cc models | 94.005 - 94.015mm (3.7010 - 3.7014") | 94.015 - 94.025mm (3.7014 - 3.7018") | 94.025 - 94.035mm (3.7018 - 3.7022") | |
Rebore sizes: | ||||
/5,/6, R60/7, R75/7 - 1st | 0.50mm (0.020") | |||
/5,/6, R60/7, R75/7 - 2nd | 1.00mm (0.040") | |||
R45 & R65 to '80, R80/7 - 1st | 0.25mm (0.010") | |||
R45 & R65 to '80, R80/7 - 2nd | 0.50mm (0.020") | |||
All 1000cc models to '80 | 0.25mm (0.010") | |||
All models '81 on | rebores not possible, pistons and cylinders must be renewed when excessively worn | |||
Maximum ovality: | ||||
R45, R65, R65LS | 0.005mm (0.0002") | |||
R80G/S, R80ST - 20mm (0.8") from top of bore | 0.005mm (0.0002") | |||
R80G/S, R80ST - 115mm (4.5") from top of bore | 0.010mm (0.0004") | |||
All other models | 0.010mm (0.0004") | |||
Maximum taper: | ||||
/5,/6 | 0.010mm (0.0004") | |||
All other models | 0.020mm (0.0008") | |||
Pistons | ||||
Standard OD - at specified size code: | ||||
| A | B | C | |
R50/5 | 66.960mm (2.6362") | 66.970mm (2.6366") | 66.980mm (2.6370") | |
R45 | 69.955 - 69.965mm (2.7541 - 2.7545") | 69.965 - 69.975mm (2.7545 - 2.7549") | 69.975 - 69.985mm (2.7549 - 2.7553") | |
R60/5, R60/6 | 73.460mm (2.8921") | 73.470mm (2.8925") | 73.480mm (2.8929") | |
R60/7 | 73.470mm (2.8925") | 73.480mm (2.8929") | 73.490mm (2.8933") | |
R65, R65LS | 81.955 - 81.965mm (3.2266 - 3.2270") | 81.965 - 81.975mm (3.2270 - 3.2274") | 81.975 - 81.985mm (3.2274 - 3.2278") | |
R75/5, R75/6 | 81.960mm (3.2268") | 81.970mm (3.2272") | 81.980mm (3.2276") | |
R75/7 | 81.965mm (3.2270") | 81.975mm (3.2274") | 81.985mm (3.2278") | |
All 800cc models | 84.765mm (3.3372") | 84.775mm (3.3376") | 84.785mm (3.3380") | |
R90/6, R90S | 89.960mm (3.5417") | 89.970mm (3.5421") | 89.980mm (3.5425") | |
All 1000cc models | 93.960mm (3.6992") | 93.970mm (3.6996") | 93.980mm (3.7000") | |
Standard piston/cylinder clearance: | ||||
/5,/6 | 0.035 - 0.045mm (0.0014 - 0.0018") | |||
R60/7 | 0.020 - 0.040mm (0.0008 - 0.0016") | |||
R75/7 | 0.019 - 0.041mm (0.0007 - 0.0016") | |||
R80/7 | 0.023 - 0.047mm (0.0009 - 0.0029") | |||
R45 & R65 up to '80 | 0.030 - 0.050mm (0.0012 - 0.0020") | |||
All 1000cc models up to '80 | 0.028 - 0.052mm (0.0011 - 0.0021") | |||
All models '81 on | 0.030 - 0.040mm (0.0012 - 0.0016") | |||
Maximum permissible piston/cylinder clearance: | ||||
/5,/6 | 0.120mm (0.0047") | |||
All other models | 0.080mm (0.0032") | |||
Piston weight group | + or - stamped in piston crown - both | |||
Pistons must be of the same weight group, i.e. carry the same marking. | ||||
Piston rings | ||||
Top: | ||||
Type | Plain, rectangular section | |||
Thickness: | ||||
/5,/6 | 1.790 - 1.810mm (0.705 - 0.0713") | |||
R45 | 1.478 - 1.490mm (0.582 - 0.0587") | |||
All other models | 1.728 - 1.740mm (0.0680 - 0.0685") | |||
End gap - installed: | ||||
R50, R60 | 0.25 - 0.40mm (0.0098 - 0.0158") | |||
R45 | 0.25 - 0.45mm (0.0098 - 0.0177") | |||
R75/5, R75/6, R90/6, R90S | 0.30 - 0.45mm (0.0118 - 0.0177") | |||
/7 '81 on | 0.40 - 0.65mm (0.0158 - 0.0256") | |||
All other models | 0.30 - 0.50mm (0.0118 - 0.0197") | |||
Side clearance: | ||||
/5,/6 | 0.060 - 0.070mm (0.0024 - 0.0028") | |||
/7 | 0.060 - 0.090mm (0.0024 - 0.0035") | |||
All other models | 0.050 - 0.082mm (0.0020 - 0.0032") | |||
Second: | ||||
Type | Plain, with stepped or tapered face | |||
Thickness | ||||
/5,/6 | 2.030 - 2.050mm (0.0799 - 0.0807") | |||
/7, R45 up to '80 | 2.010 - 2.022mm (0.0791 - 0.0796") | |||
All other models | 1.978 - 1.990mm (0.0779 - 0.0784") | |||
End gap - installed: | ||||
R50, R60 | 0.25 - 0.40mm (0.0098 - 0.0158") | |||
R45 | 0.25 - 0.45mm (0.0098 - 0.0177") | |||
R80G/S, R80ST | 0.30 - 0.50mm (0.0118 - 0.0197") | |||
/7 '81 on | 0.40 - 0.65mm (0.0158 - 0.0256") | |||
All other models | 0.30 - 0.45mm (0.0118 - 0.0177") | |||
Side clearance: | ||||
/5,/6 | 0.050 - 0.060mm (0.0020 - 0.0024") | |||
All other models | 0.040 - 0.072mm (0.0016 - 0.0028") | |||
Oil scraper: | ||||
Type | One piece | |||
Thickness: | ||||
/5,/6 | 4.010 - 4.030mm (0.1579 - 0.1587") | |||
/7 | 4.010 - 4.022mm (0.1579 - 0.1584") | |||
R80G/S, R80ST, R45 '81 on | 3.478 - 3.490mm (0.1369 - 0.1374") | |||
R45 up to '80 | 3.510 - 3.522mm (0.1382 - 0.1387") | |||
R65, R65LS | 3.978 - 3.990mm (0.1566 - 0.1571") | |||
End gap - installed: | ||||
R50/5, R60/5 | 0.20 - 0.35mm (0.0079 - 0.0138") | |||
R60/6, R60/7 | 0.25 - 0.35mm (0.0098 - 0.0138") | |||
R45 | 0.25 - 0.45mm (0.0098 - 0.0177") | |||
All other models | 0.25 - 0.40mm (0.0098 - 0.0158") | |||
Side clearance: | ||||
/5,/6 | 0.030 - 0.040mm (0.0012 - 0.0016") | |||
R60/7 | 0.020 - 0.050mm (0.0008 - 0.0020") | |||
All other models | 0.030 - 0.062mm (0.0012 - 0.0024") | |||
Torque wrench settings | ||||
Component: | Nm | lb/ft | ||
Rocker cover cap nut - R8, R80RT '85 on | 20 | 15 | ||
Spark plugs | 20 - 30 | 15 - 22 | ||
Valve adjuster locknuts | 18 - 23 | 13.5 - 17 | ||
Cylinder head retaining nuts - all models up to '80: | ||||
1st stage | 15 | 11 | ||
2nd stage | 35 | 26 | ||
3rd stage | 40 | 29.5 | ||
Standard setting | 38 - 42 | 28 - 31 | ||
Cylinder head retaining nuts - all models '81 on: | ||||
1st stage | 15 | 11 | ||
2nd stage | 25 | 18.5 | ||
3rd stage | 35 | 26 | ||
Standard setting | 35 - 39 | 26 - 29 | ||
Exhaust pipe finned nuts: | ||||
R80, R80RT '85 on | 160 | 118 | ||
R45 & R65 '79 - '80,/7 up to '80 | 140 - 180 | 103 - 133 | ||
All other models | 200 - 220 | 148 - 162 | ||
Connecting rod bolts | 48 - 52 | 35.5 - 38 | ||
Flywheel mounting bolts: | ||||
/5 | 58 - 62 | 43 - 46 | ||
R60/6 & R75/6 up to 9/74 - 10mm bolts | 60 - 65 | 44 - 48 | ||
R90/6 & R90S up to 9/74 - 10mm bolts | 70 - 75 | 52 - 55 | ||
/6 '75 on and all other models - 11mm bolts | 100 - 105 | 74 - 77.5 | ||
Oil pump pickup mounting bolts | 9 | 6.5 | ||
Camshaft flange bearing - all models '79 on | 15 - 18 | 11 - 13.5 | ||
Sump mounting bolts | 9 - 12 | 6.5 - 9 | ||
Alternator rotor retaining bolt | 23 - 27 | 17 - 20 | ||
Starter motor mounting bolts | 47.5 | 35 | ||
ATU retaining nut: | ||||
/5,/6 | 6 - 7 | 4.5 - 5 | ||
/7 up to '78 | 5 - 6 | 4 - 4.5 | ||
All other models | N/App | N/App | ||
Oil filter inner cover retaining bolt - /5,/6 only | 41 | 30 | ||
Engine oil drain plug: | ||||
Models up to '80 | N/Av | N/Av | ||
All models '81 on | 41 | 30 | ||
Oil filter cover mounting bolts | 10 | 7.5 | ||
Engine mounting nuts: | ||||
R80, R80RT '85 on | 54.2 | 40 | ||
All other models | 70 - 77 | 52 - 57 | ||
Global Rescue is the premier provider of medical, security and evacuation services worldwide and is the only company that will come to you, wherever you are, and evacuate you to your home hospital of choice.
Additionally, Global Rescue places no restrictions on country of citizenship - all nationalities are eligible to sign-up! Travel medical insurance is also available, currently the limit is 90 days. (TIP: For Evac insurance - Click Multiple Trips and 365 days to get year long insurance.)
Ripcord Rescue Travel Insurance™ combines into a single integrated program the best evacuation and rescue with the premier travel insurance coverages designed for adventurers.
Led by special operations veterans, Stanford Medicine affiliated physicians, paramedics and other travel experts, Ripcord is perfect for adventure seekers, climbers, skiers, sports enthusiasts, hunters, international travelers, humanitarian efforts, expeditions and more.
Ripcord travel protection is now available for ALL nationalities, and travel is covered on motorcycles of all sizes! NOTE: Travel medical insurance currently has a limit of 90 days.
Member login
Announcements
Thinking about traveling? Not sure about the whole thing? Watch the HU Achievable Dream Video Trailers and then get ALL the information you need to get inspired and learn how to travel anywhere in the world!
Have YOU ever wondered who has ridden around the world? We did too - and now here's the list of Circumnavigators!
Check it out now, and add your information if we didn't find you.
Are you an Overland Adventure Traveller?
Does the smell of spices wafting through the air make you think of Zanzibar, a cacophony of honking horns is Cairo, or a swirl of brilliantly patterned clothing Guatemala? Then this is the site for you!
Hosted by Grant and Susan Johnson, RTW 1987-1998
Next HU Events
ALL Dates subject to change.
2025 Confirmed Events:
- Virginia: April 24-27 2025
- Queensland is back! May 2-4 2025
- Germany Summer: May 29-June 1 2025
- CanWest: July 10-13 2025
- Switzerland: Date TBC
- Ecuador: Date TBC
- Romania: Date TBC
- Austria: Sept. 11-14
- California: September 18-21
- France: September 19-21 2025
- Germany Autumn: Oct 30-Nov 2 2025
Add yourself to the Updates List for each event!
Questions about an event? Ask here
Books
All the best travel books and videos listed and often reviewed on HU's famous Books page. Check it out and get great travel books from all over the world.
NOTE: As an Amazon Affiliate we earn from qualifying purchases - thanks for your help supporting HU when you start from an HU Amazon link!